Helixparts My Account  Cart Contents  Checkout  
  Homepage » Catalog » Rear Spoiler Installation My Account  |  Cart Contents  |  Checkout   
Categories
Honda Helix CN250-> (141)

All products on one page

!! EUROPE Store !!
Generic Term
What's New? more
Waterpump cover Honda Helix CN250
Waterpump cover Honda Helix CN250
USD32.00
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
Information
Privacy Notice
Conditions of Use
FAQ
Contact Us
Helixparts Guide Helixparts Guide
 
 

Spoiler Installation.

In order to install our Helix spoiler you have to remove the following body parts first:

  • Seat
    Remove the seat mounting bolt and remove the seat.
  • Handle Bars
    Remove the handle bars by removing the four bolts.
  • Rear lower panels.
    Remove the four screws hoding each lower panel (left and right)
  • Helmet holder
    Remove the helmet holder by removing the attaching bolt.
 


After following the above steps, your Helix will look like this:
 

  • Rear body panel
    Remove the four mounting bolts holding the Rear body panel, see image below.
    Open the trunk, then lift the complete body panel off.
  • Use a non-permanent marker to mark the locations of the holes you have to drill.
    Carefully align the spoiler into its final position. The distance between the trunk-lid edge and the spoilers tip is about 8 3/4 inches.
    Then mark the hole locations with the help of the two threaded bosses underneath the spoiler.
 
Here a picture of the panel with already drilled holes. Holesize approx 3/4 inch. Please make sure to carefully select the hole locations. The pictures provided here are only a guideline with approx values.
Helixparts.com IDDHI TECHNOLOGIES CO LLC is not responsible for damaged body panels due to missplaced holes.
Only the right body panel requires a third "center hole". It is used to route the LED brake harness behind the body panel.
Assemble the spoiler and then cut off the lower end of the LED brakelight harness close to the connector.
Extend the harness By three foot, using standard automotive wire and crimp connectors. Route the harness to the left side of the rear panel assembly.
Locate the taillight connector. you will find it close to the Ignition coil on the left side of your Helix.
Use automotive crimp connectors to create a branch-connection on the green and green-yellow tail light wires.
Connect the red LED brakelight wire to the green-yellow taillight wire and connect the black LED spoiler wire to the green taillight wire.


 

Continue
Shopping Cart more
0 items
Specials more
SPECIAL! B-Grade Upper Body panel set white
SPECIAL! B-Grade Upper Body panel set white
USD247.50
USD198.00
News

We proudly accept:


Mastercard


Visa


American
Express


Paypal


USPS money order

We protect the security
of your credit card information
using secure socket layer (SSL) encryption.


All purchasable
items are on stock.
 

We ship whithin 24h on workdays!

 


 

 

Reviews more
Variomatik clutch HONDA HELIX / ELITE / PIAGGIO 250
I have a 1986 Honda Helix with sidecar and my driven clutch ..
5 of 5 Stars!
Bestsellers
01.Exhaust manifold to muffler gasket
02.Intake manifold, HONDA Helix, Piaggio Hexagon 250
03.Cylinder Head to exh.manifold gasket
04.Aircleaner HONDA Helix, Piaggio Hexagon
05.Honda Helix CN250 drive belt
06.Oil filter set, HONDA Helix, Piaggio Hexagon 250
07.HONDA HELIX CN250 Exhaust Muffler
08.Chrome Set Honda Helix
09.Lower Panel Set Honda Helix CN250
10.Crystal Clear light set

ATTENTION customers from Europe, please visit our store in Germany.

Copyright © 2005 Helixparts.com